9/22/2023 0 Comments Jump desktop add computerTo test if connections are using your custom relay server, apply the settings to a computer and then use the Jump Desktop to connect to the computer. Testing Connections to make sure they're going through your relay server Make sure you Assign the Connect Settings to the computers you want to use the relay server with.This is useful for high security environments where you want to control all traffic flow to and from your machines. You can force Jump Desktop Connect to always use your relay server for connections. If this fails, it will fallback to using your custom relay server. Normally Jump Desktop Connect will try it's best to create a direct peer-to-peer connection between machines using NAT traversal. Optional: Turn on Relay Connections Only.Using the internal IP address may be necessary if your internal machines can only communicate with the relay server using it's internal IP address. Tip: For the Host field you can also use your relay's internal LAN IP address instead of it's external IP address.In the Host enter the relay server's IP address ( RELAY_EXTERNAL_IP) followed by a ':' and then the port ( RELAY_PORT).In the Password field enter the password you used when setting up the relay server ( RELAY_PASSWORD).In the Username field enter the username you selected when setting up the relay server ( RELAY_USERNAME).In the Add New Relay dialog enter the following:.In the Edit Relays dialog, click the Add button to add a new relay server configuration.In the Networking section click the Edit button next to the On Premise Relay Servers option.Create a new Connect Setting configuration or edit your existing configuration.Once the relay server is running we will use Connect Settings to configure Jump Desktop Connect on your team machines with the relay server configuration. user "$RELAY_USERNAME:$RELAY_PASSWORD" \ p $RELAY_CONNECTION_MIN_PORT-$RELAY_CONNECTION_MAX_PORT:$RELAY_CONNECTION_MIN_PORT-$RELAY_CONNECTION_MAX_PORT/udp \ Note: These steps are for Linux: RELAY_PORT= 3478 To start coturn on your internal machine run the following command. In the example below, the server can handle ~400 connections. The number of ports you allocate to the connection port range will determine the number of simultaneous connections the server can serve. Each simultaneous connection requires one UDP port on server. Select a connect port range to use (RELAY_CONNECTION_MIN_PORT, RELAY_CONNECTION_MAX_PORT).The external IP field is the public IP address of your WAN interface. In the case below, we've used relay port 3478, with username MyUserName and password MyPassword and external IP 1.2.3.4. Select a port (RELAY_PORT), username (RELAY_USERNAME) and password (RELAY_PASSWORD) for relay server.Make sure you have Docker installed on your server machine: How To Install Docker.We'll use Docker to deploy the official coturn docker image. We'll setup a open-source TURN server called coturn. The relay has been tested on CentOS, AlamaLinux, RockyLinux and Ubuntu, however you can use any flavour of Linux. A Linux machine that will act as a relay server inside or outside your network. Jump Desktop for Teams Enterprise subscription.Relay server configuration where the relay is hosted externally:Īlternate configuration where the relay server is hosted internally: It will transmit opaque, encrypted data packets between computers. The on premise relay server will not be able to decrypt the underlying protocol data. On Premise relay configuration is centrally controlled using Jump Desktop's Connect Settings.Įncryption: All Jump Desktop Connect traffic is encrypted end-to-end. On Premise Relay Servers are also easier to deploy than VPN infrastructure - for example there is no key distribution or client side configuration required with on premise relay servers. On Premise Relay servers achieve higher performance than VPNs by avoiding the extra networking and CPU overhead of VPNs. On Premise Relay Servers can be used to replace complex and potentially slow VPN infrastructure. You can also run a relay server behind a NAT using port forwarding. All traffic is run through a specific set of UDP ports so you can control exactly what goes in and out and apply proper QoS if needed. On Premise relay servers allow you to control how Jump Desktop traffic is routed through your infrastructure. Starting with Jump Desktop Connect 6.7.42 you can now run on-premise, high availability relay servers.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |